If you own a Ryobi pole saw, then at some point you’re going to have to replace the chain. It’s just a fact of life. And if you’re not sure how to do it, well, that’s why you’re reading this article! In this guide, we will walk you through the entire process of replacing the chain on your Ryobi pole saw. We’ll discuss what tools and materials you need, as well as how to actually do the replacement yourself. So whether you’re a seasoned pro or a complete novice, read on for all the information you need to successfully replace your Ryobi pole saw chain!
How do I put the chain back on my Ryobi pole saw?
If you need to replace the chain on your Ryobi pole saw, there are a few things you’ll need to do first. First, you’ll need to gather the following tools and materials:
- A new chain
- A pair of pliers
- A screwdriver
Once you have these items, follow these steps to put the new chain on your Ryobi pole saw:
- Unscrew the old chain from the saw. You will find the screws that hold the old chain in place near the front of the saw. Use a screwdriver to remove these screws.
- Remove the old chain from the saw. Simply pull it off of the teeth on the blade.
- Put the new chain around the blade. Make sure that the teeth on the blade are lined up with the holes in the chain.
- Screw the new chain into place. Use the screws that you removed in step one to secure the new chain in place.
- Before you put your Ryobi away, test the new chain to ensure it’s working as intended. Start up the saw and let it run for a bit before you begin cutting. If you’re satisfied with what you see and hear, then go ahead and proceed! [1]
How do you release the chain brake on a Ryobi pole saw?
The chain brake on a Ryobi pole saw is designed to stop the chain from moving if it gets jammed. If this happens, you’ll need to release the brake before you can continue using the saw. To do this, simply follow these steps:
- Locate the brake lever. This lever is usually located near the front of the saw, near where your hand would go when you’re holding it.
- Pull the brake lever. This will release the brake and allow the chain to move again.
- Test the chain. Before you put your Ryobi pole saw away, make sure that the chain is working properly. To do this, simply turn on the saw and allow it to run for a few seconds. If everything looks and sounds good, then you’re all set!
How do you change the chain on a Ryobi Ry3716?
The process for changing the chain on your Ryobi Ry3716 is actually quite simple. First, you’ll need to remove the bar and chain from the saw. To do this, unscrew the bar clamp nut with a wrench and then slide the bar and chain off of the saw. Next, use a chain breaker tool to remove the old chain from the bar. Once the old chain is removed, you can thread the new chain onto the bar. Be sure that the teeth on the new chain are facing in the correct direction before you tighten it down. Finally, reattach the bar and clamp nut and you’re ready to go!
How do you remove a clutch from a Ryobi pole saw?
There are a few ways to remove the clutch from your Ryobi pole saw. The first way is to use a large flathead screwdriver. Wedge the screwdriver under the small tab on the side of the clutch. Then, pry the clutch off of the spindle.
The second way to remove the clutch is by using a pair of needle-nose pliers. Grab onto the small tab on the side of the clutch with the needle-nose pliers and pull straight up until the clutch pops off of the spindle.
The third way to remove the clutch is by inserting a small Allen wrench or punch into the hole in the center of the clutch. Once you have inserted the tool into the hole, twist it to the left until the clutch pops off of the spindle.
Once you have removed the clutch from the spindle, you will be able to access the brake pad and brake cable. [2]
Why does the chain slip on my Ryobi pole saw?
There are a few reasons why the chain on your Ryobi pole saw might be slipping. The first reason is that the chain is too loose. To fix this, simply tighten the chain using the adjustment screws located near the front of the saw.
The second reason why the chain might be slipping is that the bar is not properly seated in the guide holes. To fix this, remove the bar and chain from the saw and then make sure that the bar is pushed all the way into the guide holes. You may need to use a hammer to tap it into place.
The third reason why the chain might be slipping is that the sprocket teeth are damaged or worn down. If this is the case, you’ll need to replace the sprocket.
The fourth reason why the chain might be slipping is that the brake pad is worn out. If this is the case, you’ll need to replace the brake pad.
The fifth reason why the chain might be slipping is that there is something blocking the path of the chain. This could be a piece of debris or even a rock. To fix this, simply remove whatever is blocking the path of the chain and then try again.
How do you remove a spark plug from a Ryobi pole saw?
The process for removing a spark plug from a Ryobi pole saw is actually quite simple. First, you’ll need to remove the spark plug boot. To do this, simply pull it straight off of the spark plug. Next, use a spark plug wrench to loosen and remove the spark plug from the engine. Once the spark plug is removed, you can install the new one by following these same steps in reverse order. [3]
What kind of spark plug does a Ryobi?
The type of spark plug that you’ll need for your Ryobi pole saw will depend on the model that you have. However, most Ryobi models use a Champion RCJ6Y spark plug.
Do spark plugs need calibration?
No, spark plugs do not need to be calibrated. However, it is important to make sure that the gap between the spark plug electrodes is set to the correct size. The gap should be set to .020 inches for most Ryobi models.
Why is my Ryobi pole saw smoking?
A Ryobi pole saw smoking can be attributed to a few things. One potential reason your chainsaw isn’t starting is that the spark plug is fouled. To remedy this, follow these steps: 1) remove the spark plug and 2) clean it with a wire brush. If the problem continues, you may need to get a new spark plug.
The second reason why your Ryobi pole saw might be smoking is that the air filter is dirty. To fix this, simply remove the air filter and clean it off with a brush or compressed air. If the problem persists, you may need to replace the air filter.
The third reason why your Ryobi pole saw might be smoking is that the fuel mix is too rich. To fix this, simply adjust the carburetor so that less fuel is being delivered to the engine.
The fifth reason why your Ryobi pole saw might be smoking is that the cylinder head gasket is blown. To fix this, you’ll need to replace the cylinder head gasket. [4]
FAQ
Will a dull chainsaw chain smoke?
No, a dull chainsaw chain will not smoke. However, it will cause the saw to run less efficiently and produce more sawdust. It’s important to keep your chainsaw chain sharpened so that it runs at peak performance. [5]
Why is my Ryobi chainsaw leaking oil?
There are a few reasons why your Ryobi chainsaw might be leaking oil. The first reason is that the oil seal is damaged. To fix this, you’ll need to replace the oil seal.
The second reason why your Ryobi chainsaw might be leaking oil is that the oil level is too high. To fix this, simply drain some of the oil out of the saw until it reaches the proper level.
If your Ryobi chainsaw is leaking oil, it might be due to the fact that the bar and chain are not properly lubricated. To fix this, simply add more bar and chain oil to the reservoir.
The fourth potential reason your Ryobi chainsaw is leaking oil is an obstruction in the oil passage. To fix this, simply remove the blockage and then add more bar and chain oil to the reservoir.
If your Ryobi chainsaw is leaking oil, it could be due to the fifth reason: a needed engine rebuild. This is a more serious problem that will require the help of a professional.
How do you start a chainsaw that has been sitting?
If your chainsaw has been sitting for awhile, there are a few things that you’ll need to do in order to get it started. First, make sure that the spark plug is clean and that the gap is set to the correct size. Next, add fresh fuel to the tank and mix it with oil at a 50:1 ratio. Finally, pull the cord until the engine starts.
How do recoil starters work?
Recoil starters work by using a spring to turn the engine over. The spring is activated when you pull on the cord. As the spring unwinds, it turns the engine over and starts it.
Useful Video: RYOBI Chain and pole saw tensioning
Conclusion
Ryobi pole saws are a great tool for anyone who needs to do some serious trimming. If you have one of these saws, it is important to know how to properly maintain it. This includes knowing how to replace the chain when necessary. With a few simple steps, you can have your Ryobi pole saw chain replaced and back to working like new in no time.
References:
- https://www.youtube.com/watch?v=z_jpl_Uhw-g
- https://www.fixya.com/support/t26273810-remove_clutch_cover_from_ryobi_chainsaw
- https://www.youtube.com/watch?v=yHYIgK8woR8
- https://www.ifixit.com/Wiki/Ryobi_CSB125_Troubleshooting
- https://chainsawguru.com/why-is-my-chainsaw-smoking/
Leave a Reply