Quotes

Success usually comes to those who are too busy to be looking for it.Henry David Thoreau

Remington Pole Saw Parts: What You Need to Know?

Remington Pole Saw Parts: What You Need to Know?

Remington pole saw parts can be confusing to figure out, especially if you’ve never had to replace them before. In this article, we will answer some of the most common questions people have about Remington pole saw parts. We’ll cover everything from how to identify which part you need to how to install it. Plus, we’ll give you a few tips on maintaining your pole saw so that it lasts as long as possible.

Remington Pole Saw Hardware

Remington pole saws are built tough, but even the most durable tools need occasional replacements and repairs. That’s where having a good understanding of Remington pole saw parts comes in handy.

There are three main types of hardware on a Remington pole saw: the bar, the chain, and the engine. The bar is the long metal piece that extends from the saw body. It’s what you use to reach high branches. The chain is the part that actually does the cutting. It’s wrapped around the bar and driven by the engine. And finally, the engine powers the whole thing. It’s usually located at the base of the pole.

Each of these parts can wear out over time and will need to be replaced eventually. But with proper care and maintenance, you can extend the life of your pole saw hardware significantly. [1]

Remington Pole Saw Hardware

Remington Pole Saw Assembly

Assembling a Remington pole saw is actually pretty straightforward. But if you’ve never done it before, the process can be a little bit confusing.

The first thing you need to do is attach the bar to the saw body. There are typically two ways to do this: with screws or with clips. If your pole saw has screws, simply line up the holes in the bar with the holes in the saw body and screw them together. If your pole saw has clips, line up the holes in the bar with the holes in the saw body and then press the clips into place.

Once the bar is attached, you can put the chain on. Again, there are usually two ways to do this: with a master link or with rivets. If your pole saw has a master link, simply press it into place. If your pole saw has rivets, you’ll need to use a hammer to pound them into place.

Finally, you can attach the engine. This is typically done with screws. Line up the holes in the engine with the holes in the saw body and screw them together.

Once all of the parts are in place, you’re ready to start cutting branches!

Saw Chain Tension Adjustment

One of the most important aspects of maintaining your pole saw is keeping the chain properly tensioned. If the chain is too loose, it can come off of the bar while you’re cutting. And if the chain is too tight, it can damage the bar or the engine.

The best way to achieve proper tension is to use a tensioning device. This is a small tool that helps you get the perfect amount of tension every time. You can find them at most hardware stores.

To use a tensioning device, first make sure that the chain is installed correctly. Then place the device on the bar and tighten it until it’s snug. Next, hold the device in place and turn the adjusting knob until the pointer is in the middle of the range. Finally, remove the tensioning device and test the tension by pulling on the chain. It should have just a little bit of give.

If you don’t have a tensioning device, you can also use a screwdriver to adjust the tension. First, make sure that the chain is installed correctly. Then find the two adjustment screws on the side of the bar. One will loosen the chain and one will tighten it. To achieve proper tension, turn both screws equally until the chain has just a little bit of give.

Checking and adjusting your chain tension regularly is key to maintaining your Remington pole saw and keeping it in good working condition for years to come. [2]

Saw Chain Tension Adjustment

Extension Cords

If you’re using an electric pole saw, you’ll need an extension cord to reach your branches. But not just any extension cord will do. You need to make sure that you use a cord that is heavy duty enough to handle the power of your saw.

The best way to determine the right size extension cord is to consult your owner’s manual. It will have specific recommendations for the size and type of cord that you should use.

Once you have the right extension cord, you need to make sure that it’s in good condition before you use it. Inspect the entire length of the cord for any frayed or damaged areas. If you find any, replace the cord before using it.

If you take good care of your extension cord, it will last for years and provide you with dependable service.

Filling Oil Tank

All gasoline-powered pole saws have an oil tank that needs to be filled with engine oil. This oil helps to lubricate the engine and keep it running smoothly.

To fill the oil tank, first consult your owner’s manual to find out what type and weight of oil to use. Once you have the right oil, remove the cap from the oil tank and slowly pour in the oil. Be careful not to overfill the tank – just fill it to the level specified in your manual.

After you’ve filled the tank, replace the cap and screw it on tight. Then check for leaks by wiping down the area around the filler neck with a clean rag. If you see any oil on the rag, tighten the cap until the leak stops.

Filling the oil tank is a simple task, but it’s important to do it correctly to keep your pole saw running smoothly. [3]

Oiling Chain

The chain on your Remington pole saw needs to be oiled regularly in order to keep it functioning properly and prevent it from rusting. You should check the chain before each use and oil it if necessary. To do this, simply hold the tip of the saw up to the light so you can see the links clearly. If any of them look dry or cracked, then they need to be oiled.

To oil the chain, first make sure that the saw is turned off and the blade is not moving. Then, apply a few drops of oil onto each link. You can use a variety of different oils for this purpose, but motor oil or bar and chain oil are both good choices. Once you have applied the oil, use a rag to wipe off any excess so that it doesn’t drip onto your work surface.

Adjusting Pole Saw Length

Depending on the model of Remington pole saw that you have, you may be able to adjust the length of the pole. This can be handy if you need to reach a higher branch or if you want to shorten the pole for storage.

To adjust the length of the pole, first consult your owner’s manual to find out how your particular model works. Some models have a knob that you can turn, while others have a release lever that you need to press. Once you know how your model works, follow the instructions in your manual to adjust the pole to the desired length.

If you need to adjust the pole frequently, it’s a good idea to practice beforehand so that you know exactly how it works. That way, you can make the adjustment quickly and easily when you need to. [4]

Adjusting Pole Saw Length

Cleaning Saw Body

The body of your Remington pole saw can become dirty from use, so it’s important to clean it on a regular basis. To do this, simply wipe the body down with a damp cloth. If there are any stubborn dirt or sap stains, you can use a mild soap to help remove them.

Once you’ve wiped down the body of the saw, be sure to dry it off completely. Moisture can cause the metal to rust, so it’s important to make sure that the saw is completely dry before storing it.

Pole saws are easy and quick to clean – a job that only takes a few minutes. If you regularly clean your saw, it will help keep it looking new and working properly.

Care of Guide Bar

The guide bar on your Remington pole saw is what the chain runs through. It’s important to keep this part clean and well-lubricated so that the chain can move freely and doesn’t get damaged.

To clean the guide bar, simply wipe it down with a rag. If there is any built-up dirt or sap, you can use a mild soap to help remove it. Once the guide bar is clean, dry it off completely.

To lubricate the guide bar, apply a few drops of oil onto it. For this purpose, motor oil or bar and chain oil work well, but you can use a variety of different oils. Apply the oil to your work surface, and then use a rag to wipe off any excess so that it doesn’t drip.

Cleaning and lubricating the guide bar is a simple task that only takes a few minutes. But if you do it on a regular basis, it will help to keep your saw running smoothly and prevent the chain from getting damaged.

Sharpening Remington Saw Chain

The chain on your Remington pole saw will eventually become dull and need to be sharpened. This is a simple task that you can do at home, but it’s important to follow the proper steps so that you don’t damage the chain.

To sharpen the chain, first consult your owner’s manual to find out what type of file you need. Some models require a special file, while others can use a standard hand file. Once you know what type of file you need, select the correct size based on the width of the chain links.

Next, set up a work surface where you can rest the saw so that the file can touch the ground. For this purpose, a piece of wood or a piece of cardboard will work well. Once your work surface is set up, hold the file at a 30-degree angle to the ground and use it to sharpen the teeth on the chain.

Remember to only sharpen the teeth on one side of the chain. If you try to sharpen both sides at once, it will throw off the balance and cause the saw to vibrate.

If you follow these steps, you can easily sharpen the chain on your Remington pole saw at home. But if you’re not comfortable doing it yourself, you can always take it to a professional for sharpening.

Replacement Chain

The first thing you will need to check when your pole saw isn’t working as it should is the chain. Over time, chains can stretch or become loose, and this can cause the pole saw to stop working correctly. You will need to measure the length of the chain to see if it needs to be replaced – a new chain should be about 20 inches long.

If the chain is too loose, you can try tightening it yourself using the adjustment screws on the side of the saw. However, if the chain is too tight or if you don’t feel comfortable adjusting it yourself, you can always take it to a professional to have them take a look at it. [5]

Replacement Chain

FAQ

How do you tighten the blade on a Remington pole saw?

The blade on a Remington pole saw is tightened using the adjustment screws on the side of the saw. These screws are responsible for tensioning the chain, and they can be turned clockwise or counterclockwise to loosen or tighten the blade.

What kind of oil does a Remington pole saw take?

The oil that a Remington pole saw takes is a special kind of oil that is made for two-stroke engines. This oil helps to lubricate the engine and keeps it running smoothly. You can find this oil at most hardware stores or online.

Where are Remington pole saws made?

Remington pole saws are made in the United States. The company has a long history of manufacturing outdoor power equipment in the US, dating back to 1921.

Useful Video: Remington Pole Saw Chain Replacement

Conclusion

Though it may seem daunting to keep up with the different Remington pole saw parts, following the guide above can help make maintenance and repairs much simpler. Be sure to consult your user manual for specific model diagrams and part names, as well as troubleshooting tips. With regular care and attention, your Remington pole saw will last for years to come. Do you have a story about caring for or repairing your pole saw? We’d love to hear from you in the comments below!

References:

  1. https://remingtonpowertools.com/how-to/pole-saw-chainsaws-ladders-dont-mix/
  2. https://www.instructables.com/How-To-Tighten-a-Chainsaw-Chain/
  3. https://www.fuelsnap.com/blog/how-to-fill-a-home-heating-oil-tank/
  4. https://www.manualslib.com/manual/1157636/Remington-104317.html?page=17
  5. https://chainsawguru.com/are-chainsaw-chains-universal/